The laying of the carpet

Below will involve two types of carpet laid, there are many similarities between two types, but there are some important differences.Laying carpet backing carpet and is the most commonly used today.

(1) the liner laying carpet

Remove without tension and do not use the nail strips, backing carpet laid carpet with similar in many ways.Use full brush adhesive will this type of carpet laid on the ground, the carpet is on the back with pad, don't need another pad, you can directly use adhesive to be laid on the cushion.This type of carpet and laid a cheaper, is typically used for low quality of the ground.

After measuring and cutting of the rug, simply roll coating adhesive and open the carpet, open to the press.Cut off excess portion of the carpet with a putty knife edge trimming.

tips

Will be transported to the cutting carpet from laying location site is the best way to towards the centre fold along the long, then loosely rolled up.Carpet volume volume is very big, but easy to maneuver through the door and turned the corner, should be rolled up and open the carpet along the fiber direction.

(2)Full shopThe carpetThe laid of

Wall-to-wall carpet laid mainly spread carpet and ensure the carpet seam connection will not be noticed.Processing joint can be very tricky, before laying should be tested in a small piece of carpet.Measurements need to be laid area, you can be folded in half and moved to laying carpet room, spread carpet and on the back of the marked with a black pen or pencil, reserved around along the wall for about 3-6 in used to stretch the carpet and seams.The carpet out of the room and put them in a big place, such as clean the garage on the ground or lane, and on the basis of the tag on the reverse of the clipping, cut good carpet back to the room and as tight as possible fixed on the nail strips around the room, looked round and smooth the carpet as much as possible.

In every corner, cut open the carpet along the diagonal to the flat, at the same time, cut some inclined seam to the carpet laid on the sides of the radiator pipe and other obstacles.

If you use a carpet can't cover the ground of the room, will need to be in some position setting seam of carpet, seam need to set up in a smaller area traffic and unattractive.You should follow the direction of the light source set up joint, this helps to reduce can make joint prominent shadow.Where the two pieces of carpet to have new juncture, back carpet, edge to form about 2 in the space.The seam iron with electric heating.

And cut a piece and seams as long seams under the carpet, with the joint of the seam iron directly on the carpet on the back seam, make the seams with liquefaction about 30 s, according to the edge of the two pieces of carpet will in the joint zone, remember that seams is very hot, when pressed, should be careful.To ensure that the joint between the fibre is not crushed, make it look like a smooth, consistent with the carpet.During the curing reaction of seam put some weight on it.If there are some cracks appear, can be used in hot glue knee brace carefully packed the seams pressed together.Handle all the seams in the same process, including the small pieces into a storage room carpet.

tips

Remember when clipping carpet from positive cut out of the carpet pattern.If tufted carpet laid tangent plane, the use of a multi-purpose cutter along the line of fiber drawing stain, and then cut the carpet, make sure not to cut off the carpet fiber.When cutting other types of carpet, start from the back clipping.Remember that should avoid to cut from the carpet fiber.

Once all seams is complete, ready to spread carpet, in order to ensure the carpet not fold or drum, there are many methods can be used to spread carpet.

Assume that the room has four Angle,A、B、CandDRoll out, you can according to the following method.Lift and Angle on the carpetAFrom the Angle of the nail stripsAtoBOut and back inAAgain fromAtoCSpread out, from the nextAtoD.If carpet looks appear distorted or pattern don't match, should be rolled out across the carpet again.

If needed, use electric tensioner and spread out to tension and rolled out across the carpet, first along the entire width, wall to wall using tensioner until the carpet is to nail bar.When the tensioner tensioning in place, complete the connection with knee brace and guarantee good article carpet and nail fixed.

In this way to fix all the carpet on the nail strips.When laying storage or protruding points, placed in the walls around the tensioner, and then the other end is placed within the storage room, storage room in the back wall is more suitable for fixed first, and then fixed side walls.

After all fixed on the nail strips, touring around with the carpet of multi-purpose cutter cut open position, you can use double glue to fix these contented, relieved, relaxed, edge, or simply vent cap back on the cover at the edge of the carpet, the carpet is good.Patrol around the room and edge trimmer clip next, highlight the burr on the edge of the carpet and completed, with a stair tool or putty knife cut good edge roll up.